cmd>config |
|
Commands: |
|
show |
Show configuration and status information |
show commands |
Show cli configuration commands |
show running |
Show running configuration |
show initial |
Show initial configuration |
show diff |
Show initial configuration |
save |
Save the running config to initial config |
status config |
Show configfuration status |
|
|
cmd>diag |
|
Commands: |
|
show |
Show configuration and status information |
show commands. |
Show cli configuration commands |
status files list |
List files |
files remove <filename> |
Remove the file with the specified name |
files copy <filename> <destination> |
Copy the specified files to a remote location |
host <host> |
Resolve DNS names |
ping <host> [proto <proto>] [count <count>] [ttl <ttl>] [deadline <deadline>] [size <size>] |
Ping a host |
traceroute <host> [proto <proto>] |
Trace the route to a host |
tcpdump tofile interface <interface> [time <time>] [filter <filter>] |
Capture network packets to a file |
speedtest [json] [bytes] |
Perform a speed to speedtest.net |
|
|
cmd>dns |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
domain set <value> |
Set the system domain name |
domain clear |
Clear the system domain name |
search add <value> [at <position>] |
Add hostname to the search domains |
search delete <value> |
Delete hostname from the search domains |
search clear |
Clear the search domains |
search set [<value> ...] |
Replace all hostnames in the search domains |
search show |
Show the search domains |
server1 set <value> |
Set the primary DNS server |
server1 clear |
Clear the primary DNS server |
server2 set <value> |
Set the secondary DNS server |
server2 clear |
Clear the secondary DNS server |
server3 set <value> |
Set the tertiary DNS server |
server3 clear |
Clear the tertiary DNS server |
status dns |
Show details of system dns settings |
|
|
cmd>hostname |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
sources add <value> [at <position>] |
Add a preferred source to the preferred source |
sources delete <value> |
Delete a preferred source from the preferred source |
sources clear |
Clear the preferred source |
sources set [<value> ...] |
Replace all a preferred sources in the preferred source |
sources reset |
Reset the preferred source back to default |
sources show |
Show the preferred source |
hostname set <value> |
Set the system hostname |
hostname clear |
Clear the system hostname |
status hostname |
Show details of system hostname settings |
|
|
cmd>interface |
|
Commands: |
|
show |
Show configuration and status information |
show commands |
Show cli configuration commands |
status all |
Show all the interfaces in the system |
status show [bridges] [groups] [vlans] [vxlans] [ethernets] [all] |
Show interface of the specified type(s) |
status monitor |
Show the monitoring state of each interface |
add <type> <name> |
Create an interface (bridge, vlan, group) |
add vxlan <name> vni <vni> [dstport <dstport>] [interface <interface>] |
Create a VXLAN interface |
|
|
cmd>interface.eth0 |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
status statistics [detailed] |
Show interface statistics |
status device |
Show the device driver details |
status sfp |
Show the SFP details |
identify [duration <duration>] [cancel] |
Identify the interface by flashing the lights (if possible) |
|
|
cmd>interface.eth0.addr |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
add <value> [at <position>] |
Add an IP address or subnet to the IP addresses |
delete <value> |
Delete an IP address or subnet from the IP addresses |
clear |
Clear the IP addresses |
set [<value> ...] |
Replace all an IP address or subnets in the IP addresses |
addr show |
Show the IP addresses |
status dhcp |
Show the dhcp addresses present on this interface |
status system |
Show the interface addresses present in the system |
status addresses |
Show the interface address |
|
|
cmd>interface.eth0.dhcp |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
enable |
Enable the DHCP client |
disable |
Disable the DHCP client |
routes enable |
Enable the use of DHCP static routes |
routes disable |
Disable the use of DHCP static routes |
status state |
Show the state of the dhcp client process |
status details |
Show details of the DHCP configuration |
|
|
cmd>interface.eth0.link |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
admin set <value> |
Set the administrative state |
admin clear |
Clear the administrative state |
mtu set <value> |
Set the mtu |
mtu clear |
Clear the mtu |
txqueuelen set <value> |
Set the tx queue length |
txqueuelen clear |
Clear the tx queue length |
allmulticast set <value> |
Set reception of all multicast traffic |
allmulticast clear |
Clear reception of all multicast traffic |
promisc set <value> |
Set reception of all traffic |
promisc clear |
Clear reception of all traffic |
status all |
Show the IP link state |
|
|
cmd> interface.eth0.monitor |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
enable |
Enable monitoring of this interface |
disable |
Disable monitoring of this interface |
merge-vlans enable |
Enable merging of VLANs on this interface |
merge-vlans disable |
Disable merging of VLANs on this interface |
|
|
cmd>interface.eth0.monitor.direction |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
direction set <value> |
Set the default SPAN traffic direction |
direction clear |
Clear the default SPAN traffic direction |
|
|
cmd>interface.eth0.phys |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
autoneg enable |
Enable the auto negotiation behaviour |
autoneg disable |
Disable the auto negotiation behaviour |
speed set <value> |
Set the speed |
speed clear |
Clear the speed |
duplex set <value> |
Set the duplex mode |
duplex clear |
Clear the duplex mode |
pause autoneg enable |
Enable the auto negotiation behaviour |
pause autoneg disable |
Disable the auto negotiation behaviour |
pause tx enable |
Enable the sending of TX pause frames |
pause tx disable |
Disable the sending of TX pause frames |
pause tx disable |
Clear the sending of TX pause frames |
pause rx enable |
Enable the processing of RX pause frames |
pause rx disable |
Disable the processing of RX pause frames |
pause rx disable |
Clear the processing of RX pause frames |
status link |
Show the link information |
status pause |
Show the pause information |
|
|
cmd>jobs |
|
Commands: |
|
show |
Show configuration and status information |
show commands |
Show cli configuration commands |
list [system] [user] [completed] [running] [all] |
List jobs |
view <id> [summary] |
View details of a job |
remove all |
Remove all completed jobs |
remove <id> |
Remove a completed job |
stop <id> |
Stop a running job |
kill <id> |
Kill a running job |
|
|
cmd>netflow |
|
Commands: |
|
show commands |
Show cli configuration commands |
show |
Show the bridges/interfaces capturing traffic |
capture <interface> |
Capture traffic on bridge/interface |
no capture <interface> |
Stop capturing traffic on bridge/interface |
|
|
cmd>ntp |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
servers add <value> [at <position>] |
Add hostname or ip address to the ntp servers |
servers delete <value> |
Delete hostname or ip address from the ntp servers |
servers clear |
Clear the ntp servers |
servers set [<value> ...] |
Replace all hostname or ip addresss in the ntp servers |
servers reset |
Reset the ntp servers back to default |
servers show |
Show the ntp servers |
type set <value> |
Set the type of time synchronisation to use |
type clear |
Clear the type of time synchronisation to use |
sync |
Synchronise time now |
status daemon |
Show the status of the NTP and SNTP daemons |
status ntpd |
Show the NTPD status |
status sinefa time |
Show the status of the SINEFA time |
|
|
cmd>proxy |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
enable |
Enable the proxy for upstream connections |
disable |
Disable the proxy for upstream connections |
port set <value> |
Set the proxy port |
port clear |
Clear the proxy port |
hostname set <value> |
Set the proxy hostname or IP |
hostname clear |
Clear the proxy hostname or IP |
username set <value> |
Set the proxy username |
username clear |
Clear the proxy username |
password set <value> |
Set the proxy password |
password clear |
Clear the proxy password |
|
|
cmd>proxyserver |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
enable |
Enable the proxy server service |
disable |
Disable the proxy server service |
listen set <value> |
Set the IP address to listen for connections on |
listen clear |
Clear the IP address to listen for connections on |
port set <value> |
Set the Port to listen for connections on |
port clear |
Clear the Port to listen for connections on |
bind set <value> |
Set the IP address to bind outgoing connection to |
bind clear |
Clear the IP address to bind outgoing connection to |
allow add <value> [at <position>] |
Add an IP address or subnet to the allowed clients |
allow delete <value> |
Delete an IP address or subnet from the allowed clients |
allow clear |
Clear the allowed clients |
allow set [<value> ...] |
Replace all an IP address or subnets in the allowed clients |
allow reset |
Reset the allowed clients back to default |
allow show |
Show the allowed clients |
deny add <value> [at <position>] |
Add an IP address or subnet to the denied clients |
deny delete <value> |
Delete an IP address or subnet from the denied clients |
deny clear |
Clear the denied clients |
deny set [<value> ...] |
Replace all an IP address or subnets in the denied clients |
deny show |
Show the denied clients |
filter add <value> [at <position>] |
Add a domain name to the allowed server domains |
filter delete <value> |
Delete a domain name from the allowed server domains |
filter clear |
Clear the allowed server domains |
filter set [<value> ...] |
Replace all a domain names in the allowed server domains |
filter reset |
Reset the allowed server domains back to default |
filter show |
Show the allowed server domains |
connectport add <value> [at <position>] |
Add a port number to the allowed server ports |
connectport delete <value> |
Delete a port number from the allowed server ports |
connectport clear |
Clear the allowed server ports |
connectport set [<value> ...] |
Replace all a port numbers in the allowed server ports |
connectport reset |
Reset the allowed server ports back to default |
connectport show |
Show the allowed server ports |
status daemon |
Show the status of the proxy server daemon |
|
|
cmd>route |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
add <target> via <gateway> [type <type>] |
Add a route |
delete <target> via <gateway> [type <type>] |
Delete a route |
replace <target> via <gateway> [type <type>] |
Replace (or add) the the gateway for a route |
status routes |
Show the system routing table |
status default gateway |
Show the system default gateways |
|
|
cmd>snmpd |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
enable |
Enable the SNMP service |
disable |
Disable the SNMP service |
syslocation set <value> |
Set the system location |
syslocation clear |
Clear the system location |
syscontact set <value> |
Set the system contact information |
syscontact clear |
Clear the system contact information |
rocommunity set <value> |
Set the read only community |
rocommunity clear |
Clear the read only community |
rwcommunity set <value> |
Set the read/write community |
rwcommunity clear |
Clear the read/write community |
status daemon |
Show the status of the snmp daemon |
|
|
cmd>system |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
timezone set <value> |
Set the system timezone |
timezone clear |
Clear the system timezone |
debug add <value> [at <position>] |
Add component name to the debug components list |
debug delete <value> |
Delete component name from the debug components list |
debug clear |
Clear the debug components list |
debug set [<value> ...] |
Replace all component names in the debug components list |
debug show |
Show the debug components list |
preferred_ips add <value> [at <position>] |
Add ip address to the preferred primary ips list |
preferred_ips delete <value> |
Delete ip address from the preferred primary ips list |
preferred_ips clear |
Clear the preferred primary ips list |
preferred_ips set [<value> ...] |
Replace all ip addresss in the preferred primary ips list |
preferred_ips show |
Show the preferred primary ips list |
remote_sources add <value> [at <position>] |
Add a preferred source to the preferred source |
remote_sources delete <value> |
Delete a preferred source from the preferred source |
remote_sources clear |
Clear the preferred source |
remote_sources set [<value> ...] |
Replace all a preferred sources in the preferred source |
remote_sources reset |
Reset the preferred source back to default |
remote_sources show |
Show the preferred source |
remote_ipv4 set <value> |
Set the remote IPv4 address |
remote_ipv4 clear |
Clear the remote IPv4 address |
remote_ipv6 set <value> |
Set the remote IPv6 address |
remote_ipv6 clear |
Clear the remote IPv6 address |
auto_update set <value> |
Set automatic update policy |
auto_update clear |
Clear automatic update policy |
status timezones |
Show the available timezones |
status platform |
Show the system platform details |
status memory |
Show details of system memory |
status swap |
Show details of system swap |
status cpu |
Show details of system cpu |
status load_avg |
Show details of system load averages |
status uptime |
Show details of system uptime |
status disk |
Show details of system disks |
status firmware |
Show the system firmware details |
status primary ip |
Show the systems primary IP addresses |
status server config |
Show the server side config |
reboot [force] |
Reboot this system |
factory defaults |
Reset to factory defaults |
factory defaults keep network |
Reset to factory defaults. Keep network settings |
factory defaults keep network no reboot |
Reset to factory defaults. Keep network settings. Don't reboot |
password set <password> [username <username>] |
Set the system admin login password |
update check |
Check for software updates |
update install |
Install software updates |
purge logs |
Purge logs files from the system |
|
|
cmd>system.recovery |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
status files list |
List files |
files remove <filename> |
Remove the file with the specified name |
files copy <filename> <destination> |
Copy the specified files to a remote location |
image url set <value> |
Set the image url |
image url clear |
Clear the image url |
image list |
List the available recovery images |
image update index |
Update the list of available images |
image fetch [version <version>] [latest] [current] |
Fetch a recovery image |
image purge [except] [version <version>] [latest] [current] |
Purge downloaded images |
partition install [version <version>] [latest] [current] |
Replace the recovery image |
reimage restore reboot |
Reimage the system with the recovery image |
|
|
cmd>system.registration |
|
Commands: |
|
show |
Show configuration and status information |
show commands |
Show cli configuration commands |
status registration |
Show registration information |
key set <key> |
Set the registration key |
register |
Force an attempt to register |
|
|
cmd>system.upstream |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
url set <value> |
Set the upstream cloud url |
url clear |
Clear the upstream cloud url |
redirected_url clear |
Clear the redirected (region specific) url |
status upstream |
Show upstream information |
|
|
cmd>watchdog |
|
Commands: |
|
show |
Show configuration and status information |
show config |
Show configuration |
show commands |
Show cli configuration commands |
timeout set <value> |
Set the system watchdog timeout |
timeout clear |
Clear the system watchdog timeout |
enable |
Enable rebooting the system on watchdog timeout |
disable |
Disable rebooting the system on watchdog timeout |
Comments
0 comments
Please sign in to leave a comment.